@balaton
Quote:
Could anybody with a real Pegasos2 and an ATI card check if these messages appear there when booting MorphOS?
There is what i have when boot my pegasos2 till promot where to choose morphos/os4:
PegasosII Boot Strap (c) 2002-2004 bplan GmbH
Running on CPU PVR:80020101
Enable L1 ICache... Done.
Clean/Flush Block enabled
Reading W83194 : 5CFFFFFFFFFFFF00 Done.
Setting Front Side Bus to 133MHz... Done.
Memory has not changed
Configuring Memory
Memory Config Done
Configuring PCI0... Done.
Configuring PCI1... Done.
Configuring ETH... Done.
Releasing IDE reset ... Done.
Configuring Legacy Devices
Initializing KBD... Done.
Memory Test skipped (Warmboot detected)
SmartFirmware:
cpu0: PowerPC,74x7 CPUClock 999 Mhz BUSClock 133 Mhz (Version 0x8002,0x0101)
no/bad nvramrc - performing default startup script
channel 0 unit 0 : ata | KINGSTON SA400S37240G | SBFK61K1
ATA device not present or not responding
EMULATION INT HANDLER ENTERED WITH:
INT NO: 15
EAX=0003 EBX=1111 ECX=2222 EDX=3333 ESP=0000 EBP=5555 ESI=6666 EDI=7777
AX=4E08 BX=C305 CX=0003 DX=102A SP=6CAF BP=5555 SI=6CBD DI=9C48
DS=C000 ES=BAD0 SS=C000 CS=F000 IP=FE15 NV UP -- PL ZR NA PE NC
CS:IP = F4 FS=BAD4 GS=BAD5C40E C000 0244 3000 0000 01B4 AE57 0200
UNHANDLED INT 10 FUNCTION 0007 WITHIN EMULATION
VM using 4857513 x86 cycles for GFX init
auto-booting...
And that what i have when manually type "boot /pci/ide/disk@0,0:3 boot.img bootdevice=dh2":
Memory used before SYS_Init: 9MB
ABox 1.30 (2.7.2018) ▒ 1999-2018 by Ralph Schmidt, Emmanuel Lesueur, Teemu Suikki, Harry Sintonen
PCI ATA/ATAPI Driver@0: PIO Mode 4
PCI ATA/ATAPI Driver@0: UDMA Mode 5
ide.device@0: ATA-HD KINGSTON SA400S3 <DIRECT_ACCESS>
ide.device@0: Mount <boot>
ide.device@0: Partition <boot> DosType 0x444f5301
ide.device@0: Mount <DH0>
ide.device@0: Partition <DH0> DosType 0x53465300 BootPri 0
ide.device@0: Mount <DH1>
ide.device@0: Partition <DH1> DosType 0x53465300
ide.device@0: Mount <DH2>
ide.device@0: Partition <DH2> DosType 0x53465300 BootPri 0
ide.device@0: Mount <DH3>
ide.device@0: Partition <DH3> DosType 0x53465300
Radeon: Failed to initialise Radeon DMA
Radeon: Failed to allocate CCE DMA memory
And then Ambient show ups and working. But sure, there are the same “failed to” words at the end.
My card is radeon9250, and from "info about card" on morphos side it show device as "RV280 [Radeon 9200 PRO] (0x5960)". And loaded driver is "ATIRadeon 52.37 (06.09.2020)"
Edited by kas1e on 2023/6/28 15:26:36
Edited by kas1e on 2023/6/28 15:28:35
Edited by kas1e on 2023/6/28 15:30:49
Edited by kas1e on 2023/6/28 15:50:25