Oh dear! Is my A1 going up the spout? :-( NOT YET!

@Rudei

So I replaced the battery and fiddled with the connections on the motherboard for the keyboard and mouse.

This seems to have done the trick for now, may need to get those connections looked at, at some stage.

For now (touch wood) I have myself a working AmigaOne - although having some degree of difficulty with the UBOOT settings but I'm sure I'll work it out.

Thank you for all of your suggestions people.
Kind Regards,
Rude!

Hi @Rudei

Glad to hear this! Now I'm jealous for sure!

I'm still locked into this problem:

http://amigaworld.net/modules/newbb/v ... p?topic_id=24266&forum=33

It's nice to have company in misery, but nicer if some expert could explain why we bootup with no UBoot syntax?

@Snuffy

Try Roy Leith's suggestion.
Also, is it possible the Uboot chip is loose or knackered? Wild stab in the dark

Rude!

@Rudei

Nice to have you back on your A1 Rudei

@Mikey_C

Cheers Mike

Rude!

@Rudei

SAM 440 ?

Hi @Rudei

So, what was source of problem? I'm still stuck in the spout I'd be grateful to any info.

Hi @Snuffy

Yeh right, talking to myself or the A1200!

Anyway this spider just popped out of spout -- booga!

It hadn't any thing to do with batteries. The summer days caused stressing: the two year old LCD monitor failed, the keyboard failed, the battery holder failed. Jeans-Jaques at Amiga Center was very helpful. I didn't know what the extent of all summer overheating did ,so I wanted him to verify that the Uboot rom was was OK.

A1200 serial-in:
U-Boot 1.1.1 (Mar 3 2005 - 16:42:53), Build: 03/03/05

CPU: MPC7450 v2.1 @ 800 MHz
Board: AmigaOne
DRAM:
Information for SIMM bank 0:
Number of banks: 2
Number of row addresses: 12
Number of coumns addresses: 10
SIMM is registered
Supported burst lenghts: 8 4 2 1 PAGE
Supported CAS latencies: CAS 3
RAS to CAS latency: 3
Precharge latency: 3
SDRAM highest CAS latency: 750
SDRAM 2nd highest CAS latency: 0
SDRAM data width: 8
Auto Refresh supported
Refresh time: 2084 clocks
Bank 0 size: 128 MB
Bank 1 size: 128 MB

Slot 1: vacant
DIMM0_B0_SCR0 = 0x00e77f00
DIMM0_B1_SCR0 = 0x00e77f0FLASH: 0 kB
VGA: 0..
In: serial
Out: serial
Err: serial
SCSI: Error SCSI Controller (1000,000F) not found
Net: 3Com 3c920c#0
AT Keyboard initialized!
USB: scanning bus for devices... 3 USB Devices found

Bus 0: OK Bus 1: OK
Device 0: Model: WDC WD400BB-00JHC0 Firm: 05.01C05 Ser#: WD-WMAMA5497000
Type: Hard Disk
Capacity: 38166.6 MB = 37.2 GB (78165360 x 512)
Device 1: Model: WDC WD200BB-75D000 Firm: 05.03E05 Ser#: WD-WMAD1H139000
Type: Hard Disk
Capacity: 19073.4 MB = 18.6 GB (39062500 x 512)
Device 2: Vendor: AOPEN Prod.: DUW1616/ARR Rev: 1020
Type: Removable CD ROM
Capacity: not available
Device 3: Vendor: LITE-ON Prod.: CD-RW SOHR-1239 Rev: 2$0A
Type: Removable CD ROM
Capacity: not available
Press any key to interrupt autoboot: 0

First-level bootloader: entered main
First-level bootloader: got 3 valid boot sources
AmigaOS4 first-level bootloader.
Scanning HDD WDC WD400BB-00JHC0 WD-WMAMA5497000 05.01C05... Entered find_sec_
start
Reading sector 0
Reading sector 1
Found an HD
FLB: found something
FLB: SLB of length 27828; loading
found AmigaOS4 second level bootloader.
FLB: SLB loaded; now launching it
Loading .text @ 0x014000a0 (22464 bytes)
Loading .rodata @ 0x01405860 (2488 bytes)
Loading .eh_frame @ 0x01406218 (52 bytes)
Loading .got2 @ 0x0141624c (724 bytes)
Loading .data @ 0x01416520 (208 bytes)
Loading .sdata @ 0x014165f0 (16 bytes)
Clearing .sbss @ 0x01416600 (168 bytes)
Clearing .bss @ 0x014166a8 (3928 bytes)
A1 Second-level booter V2.
Idea, design and main co
Booting configuration AmigaOS4.0

Booga!

@Snuffy

Welcome back!

Bye,
TMTisFree

@TMTisFree

Thanks! I've made a special report to AV over here:

http://amigaworld.net/modules/newbb/v ... =20&viewmode=flat&order=0

I've been busy now catching up the last two months!